ISW - Current Controlled Switch Model

Old Content - visit altium.com/documentation

Model Kind

Switch

Model Sub-Kind

Current-Controlled

SPICE Prefix

W

SPICE Netlist Template Format

V@DESIGNATOR %1 %2 0V
@DESIGNATOR %3 %4 V@DESIGNATOR @MODEL &"INITIAL CONDITION"

Parameters (definable at component level)

The following component-level parameters are definable for this model type and are listed on the Parameters tab of the Sim Model dialog. To access this dialog, simply double-click on the entry for the simulation model link in the Models region of the Component Properties dialog.

Initial Condition the starting point for the switch, either open (OFF) or closed (ON).

Parameters (definable within model file)

The following is a list of parameters that can be stored in the associated model file:

IT

threshold current (in Amps). (Default = 0).

IH

hysteresis current (in Amps). (Default = 0).

RON

ON resistance (in Ohms). (Default = 1).

ROFF

OFF resistance (in Ohms). (Default = 1/GMIN). GMIN is an advanced SPICE option that sets the minimum conductance (maximum resistance) of any device in the circuit. It is specified on the Spice Options page of the Analyses Setup dialog and its default value is 1.0e-12 (mhos).

Notes

  1. The model allows an almost ideal switch to be described. With careful selection of the ON and OFF resistances, they can effectively be seen as zero and infinity respectively, in comparison with other elements in the circuit.
  2. The use of an ideal, highly non-linear element such as a switch can cause large discontinuities to occur in the circuit node voltages. The rapid state change caused by opening and closing a switch can cause numerical round off or tolerance problems, leading to time step difficulties, or erroneous results. When using switches, take the following precautions:
  • Set switch impedances (RON and ROFF) just high or low enough to be negligible with respect to other elements.
  • When modeling real devices such as MOSFETS, set the on resistance to a realistic level for the size of the device being modeled.
  • If a wide range of ON to OFF resistance must be used (ROFF/RON >1e+12), then the error tolerance during transient analysis should be decreased. Set the TRTOL parameter on the Spice Options page of the Analyses Setup dialog to 1.
  • When a switch is placed around a capacitor, then the CHGTOL parameter should also be reduced (try 1e-16).
  1. The link to the required model file (*.mdl) is specified on the Model Kind tab of the Sim Model dialog. The Model Name is used in the netlist to reference this file.
  2. Where a parameter has an indicated default (as part of the SPICE model definition), that default will be used if no value is specifically entered. The default should be applicable to most simulations. Generally you do not need to change this value.
  3. The simulation-ready current controlled switch component (ISW) can be found in the Simulation Special Function integrated library (\Library\Simulation\Simulation Special Function.IntLib).

Examples

Consider the current controlled switch in the above image, with the following characteristics:

  • Pin1 (positive controlling node) is connected to net IN
  • Pin2 (negative controlling node) is connected to net GND
  • Pin3 (positive output node) is connected to net NetRLY1_4 (pin 4 of RLY1)
  • Pin4 (negative output node) is connected to net IN
  • Designator is S1
  • Initial Condition of switch is OFF (open contact)
  • The linked simulation model file is ISW.mdl

The entries in the SPICE netlist would be:

*Schematic Netlist:
VWS1 NetRLY1_4 IN 0V
WS1 IN 0 VWS1 ISW OFF
.
.
*Models and Subcircuit:
.MODEL ISW CSW()

The SPICE engine would use the value for the Initial Condition specified on the Parameters tab of the Sim Model dialog. As there are no parameter values specified in the model file, the engine will use the default values for all other parameters.

PSpice Support

To make this device model compatible with PSpice, the following additional model parameters are supported and can be entered into a linked model file (*.mdl) for the device:

IOFF control current for OFF state (in Amps). (Default = 0).
ION control current for ON state (in Amps). (Default = 1E-3).

Where a parameter has an indicated default, that default will be used if no value is specifically entered.

The format for the PSpice model file is:

.MODEL ModelName ISWITCH(Model Parameters)

where

  • ModelName is the name of the model, the link to which is specified on the Model Kind tab of the Sim Model dialog. This name is used in the netlist (@MODEL) to reference the required model in the linked model file.
  • Model Parameters are a list of supported parameters for the model, entered with values as required.

The following parameters - common to most devices in PSpice - are not supported:
T_ABS
T_MEASURED
T_REL_GLOBAL
T_REL_LOCAL

 

You are reporting an issue with the following selected text and/or image within the active document: